Hypersonic Models

This set contains a pair of 1:72 outer wing pylons with weapons adapters for USN and USMC Phantoms (and some early USAF ones as well). Suitable for all brands of 1:72 Phantom kits...

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

Paint masks for "NASA" "USAF" "U.S. AIR FORCE" stars'n'bars and serial numbers. Masks are manufactured by Miracle Masks. This is a newly updated version of the msks set which now includes the early style "NASA" rudder logo design as used on early XLR-11 powered X-15's...

This is an airframe update set for Kitty Hawk's FJ-2 Fury. It includes a new intake nose ring with a corrected shape (the kit's nose is much too blunt) and cast-on one-piece air intake front part. There is detail scribing on the inside of the nose ring (absent on the kit parts). The nose wheel well ..

The is a strike camera chin pod for the nose of the Zoukei Mura F-4C. This pod was used for example by Col Robin Olds on Operation Bolo. Later, many of these chin pods were re-fitted with forward RHAW pods, retaining only the rearward facing camera. Included in this set are two types of front ends -..

This is an early, plain fin cap without any RHAW or ECM pods as used on early F-4B (and C). Designed as a drop in replacement part for the Tamiya kit...

This is an upgrade set for Zoukei Mura Phantoms. As per the kit, the stabilators can only be mounted in one (or two) position(s). With this set, you can set the stabilators in any position of your choice and improve the detail on the stabilator pivot cover plates as well. Also included are the reinf..

F-4 Phantom C/L pylon, 1:48, for the Zoukei Mura line of kits. The pylon fit on and into the detail moulded onto the ZM lower wing surface. It comes with two sets of separate pins - one for the larger stabiliser pins and the smaller sway brace pins that connect to the stores to be mounted...

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Corrected A/C air intakes for Academy's F-4 Phantom series (F-4B, C and D so far). Drop fit resin replacement. All it takes is a little superglue and a swipe of filler to blend it in...

F-4 Phantom C/L pylon, 1:48, for the Tamiya line of kits. The pylon fits on and into the moulded-on mounting tab between the Aux doors on Tamiya's kit with a simple modification (it needs to be shortened and slightly re-shaped). The pylon set comes with two sets of separate pins - one for the larger..

Decals for F-15E that took part in the operation Odyssey Dawn, Libya 2011. Features two aircraft, 97-0219 and 01-2003. Markings include full crew names that were re-applied after the operation, full contemporary stencils and landing gear placards. The set comes with paint masks for insignia, ID mark..

Hollowed, thin-walled resin part to detail the open-ended Jet Fuel Starter (JFS) exhaust tubing as found on modern Eagles, such as the F-15C and F-15E Strike Eagle. A small part that adds detail and interest to this area and brings it up to date on all 1:48 F-15 kits...

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is an empty SR-71 brake chute bay with open doors, as commonly seen after landing. Designed specifically for the Revell kit. The set comes in four 3D printed parts: the main bay, a separate end cap (for easier painting) and separate doors. The door parts have mounting lips and recesses designed..

This set contains the parts needed to build an accurate late type F-104A from the Kinetic F-104A/C kit. "Late" means that it's an airframe that was converted to the upward firing C-2 seat. Therefore you can either use the kit supplied seat or one of the various available aftermarket options.The pa..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of highly detailed and appropriately proportioned stick/grip and throttle for the Kinetic F-104 kits in 1:48. The kit parts are both oversized and a bit sparse in detail. These 3D printed resin parts are drop-in replacements that fit right into the kit's mounting holes. The parts fit b..

This is a set of two aft canopy braces for Kinetic F-104 Starfighter kits. This part is applicable to all F-104 single seat variants and is not provided in any of the Kinetic's kits. The part is very delicate, but printed from slightly forgiving resin for safer support removal and handling...

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

This is a corrected nose intake part for the Kitty Hawk FJ-3 Fury kit. It is a drop-in replacement for the kit part and features a corrected nose profile, in particular around the upper lip where the small radome is located. The kit part is too blunt, in the same way as the FJ-2 part is. The panel l..

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...